avoid_crossing_perimeters = 0
bottom_solid_layers = 5
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 1
default_acceleration = 0
dont_support_bridges = 1
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 40%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 100%
first_layer_speed = 10
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.2
min_skirt_length = 3
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.6
perimeter_speed = 30
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 2
small_perimeter_speed = 30
solid_fill_pattern = concentric
solid_infill_below_area = 10
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 5
travel_speed = 130
bed_size = 170,200
end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; make sure the bed is turned off.\nG28 X0  ; home X axis\nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
print_center = 85,100
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
start_gcode = G21; set mm units\nG28 ;home all axis\nG90; set absolute coordinates\nG1 Z5 F200 ;move platform down so we don't collide\nG1 X184 Y184 F3000 ;move to back right corner\nG1 Z0.1 F200 ;move platform close to nozzle\nM104 S[temperature] ; set extruder temp and start heating\nM190 S[first_layer_bed_temperature] ; set and wait for bed temp to be reached\nM109 S[temperature]; wait for extruder temp to be reached\nG92 E0                  ;zero the extruded length\nG1 F200 E3              ;extrude 3mm of feed stock\nG92 E0                  ;zero the extruded length again\nG1 Z15 F300 ;move platform down 15mm\nG1 X175 Y175 F3000 ;move over a little to avoid hitting the anchor
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0
bed_temperature = 70
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 2
extrusion_multiplier = 0.96
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.71
first_layer_bed_temperature = 70
first_layer_temperature = 220
max_fan_speed = 100
min_fan_speed = 70
min_print_speed = 5
slowdown_below_layer_time = 10
temperature = 220